Shedding Light on How to Easily Reset Your Govee Lights: A Step-by-Step Guide

If you’re looking to reset your Govee lights, you’ve come to the right place. Govee lights are a fantastic addition to any home, but sometimes they can be stubborn and refuse to work properly. Maybe the colors aren’t changing, or perhaps they’re flickering or stuck on one particular mode.

Whatever the issue, resetting your Govee lights is often the easiest and most effective solution. But how do you do it? Don’t worry, we’ve got you covered. In this blog post, we’ll walk you through the simple steps you need to take to reset your Govee lights and get them working perfectly again.

So relax, grab a cup of coffee, and let’s dive in!

Ensure the Govee light is switched off

If you’re having trouble with your Govee light and need to reset it, the first step is to ensure that the light is switched off. This may seem obvious, but it’s an important step to avoid any potential electrical hazards or damage to the light. Once the light is switched off, you can proceed with the reset process.

Depending on the specific Govee model you have, the steps for resetting may vary. It’s best to consult the user manual or the manufacturer’s website for specific instructions. Generally, the reset process involves pressing and holding a button on the light for a certain amount of time, but be sure to follow the instructions carefully to avoid any mistakes.

With some patience and careful attention to detail, you should be able to reset your Govee light and get it working properly again in no time.

Make sure the Govee light is not receiving any power

“power off Govee light” Before attempting to do anything with your Govee light, the very first step you should always take is to ensure that it is switched off and not receiving any power. This may seem obvious, but you’d be surprised how many times people attempt to tinker with electronics while they’re still switched on. Not only can this be dangerous, but it can also cause irreparable damage to the device.

Therefore, to ensure the safety of both yourself and your Govee light, make sure you turn it off and unplug it from any power source before attempting to diagnose or fix any issues. Additionally, double-check to ensure that all other devices connected to the Govee light, such as the power supply and adapters, are also switched off and unplugged. Taking this simple yet crucial step can help extend the life of your Govee light and prevent any unfortunate accidents down the line.

how to reset govee lights

Locate the reset button

If you’re having trouble with your Govee lights and need to reset them, the first thing to do is locate the reset button. Depending on the model of your lights, it could be located in various places. For example, some Govee lights have a small button on the control box, while others require you to press and hold a specific button on the remote control.

If you’re unsure where to find the reset button, refer to your user manual or do a quick online search for your specific model. Once you’ve located the reset button, simply press it and hold it down for a few seconds. You should see the lights flash or the control box beep to indicate that the reset has been successful.

Keep in mind that resetting your Govee lights will erase all settings and configurations, so you’ll need to set them up again from scratch. But once you’ve successfully reset your lights, you should be able to get them working properly again.

Look for the reset button in the control module for your specific Govee light

When it comes to resetting your Govee light, finding the reset button on the control module specific to your light is your first step. The reset button may vary in location depending on the model you have, so it’s essential to check the user manual for guidance. Generally, you can find the reset button on the control module’s bottom or backside, but some models may have their buttons on the front.

Once you locate the button, press and hold it for a few seconds until the LED indicators start flashing. This process will reset your Govee light and erase any current settings and configurations, allowing you to start anew. Resetting your Govee light isn’t complicated, but it’s crucial to follow the instructions provided in your user manual for a seamless reset experience.

Remember, locating the reset button may take some time, but it’s worth it to ensure your Govee light works correctly.

Press the reset button

If you’re having trouble with your Govee lights, it might be helpful to press the reset button. This can easily clear any issues and start fresh with your device. The reset button is typically located on the control box or the back of the light strip.

If you’re uncertain, refer to the user manual for specific instructions. To reset, gently press and hold the button for 5-10 seconds until the lights flash. Once this happens, your lights are reset and ready to go.

Remember to also check the connection to the power source and Wi-Fi network if you’re still experiencing issues. By pressing the reset button, you can easily troubleshoot and enjoy your Govee lights again.

Using a paperclip or any other slim object, press and hold the reset button for 10 seconds

“reset button” If you’re experiencing issues with your device or router, the first course of action is to try resetting it. While the process may seem complicated, it’s actually quite simple. All you need is a paperclip or any other slim object to press and hold the reset button for 10 seconds.

The reset button is usually located at the back or bottom of the device, clearly labelled, and indicated by a tiny hole. When you’re ready to reset, insert the tip of the paperclip or slim object into the hole and press down and hold it for the specified duration of 10 seconds. Once the time elapses, release the button and wait for the device to reboot.

The reset button helps to recalibrate the device and restore it to its default settings, fixing any glitches and improving its performance. If you find that the device is still not functioning properly after the reset, you may need to seek further technical support or contact the manufacturer for assistance. So remember, when in doubt, press the reset button.

The control module will flash three times, indicating the light has been successfully reset

If you’ve recently replaced the light bulb in your car or made any repairs to your vehicle’s lighting system, you may need to reset the control module to get the lights to function properly. Resetting the control module is a simple process that can be done in just a few steps. First, locate the reset button on the module, which is usually located somewhere near the dashboard.

Press and hold the button for a few seconds until the module flashes three times, indicating that the reset was successful. This will reset the control module, allowing your lights to function as they should. If you’re unsure about the location of the reset button or are having any other issues with your car’s lighting system, it’s always best to consult with a professional mechanic to ensure your safety on the road.

Restore the default settings

If you’re having issues with your Govee lights or simply want to start fresh, resetting them to their default settings might be the answer. Here’s how to reset Govee lights: First, unplug the light strip or lamp from the power source. Then, remove the batteries from the remote control.

Wait for at least 10 seconds to ensure the temporary storage in the lights is cleared. Finally, plug the light strip or lamp back into the power source and reinsert the remote control batteries. Your Govee lights should now be reset to their default settings and ready to use.

Keep in mind that this process may vary slightly depending on the specific type of Govee light you have. If you’re still having trouble, refer to the user manual or contact Govee’s customer support.

Turn on the Govee light and verify that it has been reset to the default settings

The first step in restoring your Govee light to its default settings is to turn it on. Once it’s on, you can begin the reset process. To reset the light, press and hold the power button for 5-10 seconds.

The light will turn off and then back on again, indicating that it has been restored to the default settings. This process should only take a few moments and will not cause any permanent damage to your device. When you’re finished with the reset, you can customize your light’s settings and create the perfect ambiance for any occasion.

With Govee’s versatile lighting options, you can enjoy personalized lighting that perfectly matches your mood, décor, and activities. So go ahead and reset your Govee light today and rediscover the magic of interior lighting!

Adjust settings to your preferences

As we all have different preferences, adjusting settings to our liking enhances our user experience. Whether it’s the language, font size, or background color, customizing settings according to our needs can make device usage more comfortable and efficient. However, there may come a time when the settings have become too complex, and you want to revert to the default settings.

Restoring the default settings is easy, and it will bring your device back to its original state. You can customize your settings again later, but starting fresh may help if your device is experiencing issues or you want a simpler interface. By doing this, you can ensure a smooth and enjoyable experience when using your device.

So, don’t hesitate to reset your settings to the defaults whenever necessary.

Final Thoughts

If you’re having trouble with your Govee lights and need to reset them, it’s actually a relatively simple process. First, make sure the lights are turned off and unplugged from the power source. Then, find the reset button on the controller or the device itself.

This button may be located on the back, bottom, or side of the controller/device. Press and hold the reset button for 5-10 seconds, until the lights begin to flash. This indicates that the reset has been successful.

Once the lights have stopped flashing, you can plug them back in and turn them on. Voila! Your Govee lights have been reset and should now be functioning properly. It’s important to note that resetting may delete any saved settings you had on the device, so be prepared to reprogram them as needed.

Overall, resetting your Govee lights is a quick, stress-free way to troubleshoot any issues you may be experiencing.


In conclusion, resetting your Govee lights is easy as pie! All you have to do is follow a simple series of steps that even a tech rookie could accomplish. It’s just like hitting a big red reset button – except it’s not shaped like a cartoon bomb from an old-timey comic book. So next time your Govee lights are acting up, don’t panic.

Just take a deep breath, follow our instructions, and voila! Your lights will be all reset and ready to brighten up your space once again.”


What is the process to reset GoVEE lights?
The reset process for GoVEE lights may vary depending on the model but in general, you can reset them by turning them on and off repeatedly for several times until the lights flash. Then, wait for a few seconds and turn them on again. That should reset your GoVEE lights.

What to do if GoVEE lights are not responding after resetting?
If resetting your GoVEE lights does not work, try turning off the power supply and disconnecting the lights for a few minutes. Then reconnect them and turn the power back on. If that doesn’t work, check the batteries and the connections. If the problem persists, contact customer support for assistance.

Is there any way to reset GoVEE lights without turning them off and on?
Yes, some GoVEE lights have a “reset” button or pinhole that you need to press down with a paper clip or a similar tool. Hold the button down for a few seconds until the lights flash or until the indicator light turns off and on. Release the button and wait for a few seconds for the lights to reset.

What are the common reasons why GoVEE lights need to be reset?
GoVEE lights may need to be reset due to various reasons including but not limited to power surges, battery issues, connection problems, firmware updates, or software glitches. Resetting them can often fix these issues and restore the lights to their normal function.

How often should GoVEE lights be reset?
There is no set duration or frequency for resetting GoVEE lights. It depends on how often you use them and what issues you encounter. You should reset them whenever you notice any problems with their function such as the lights not responding, flickering, or not turning on/off properly.